RKM Smart Home
RKM Smart Home
  • Home
  • Shop
  • Z-Wave
    • Appliance Control
    • Climate Control
    • Controllers
    • Doors & Windows
    • Lighting Control
    • Remote Controls
    • Sensors & Security
    • Accessories
  • Security
  • Blog
  • More
    • Accessories
    • New Products
    • Used Products
    • Our Brands
    • FAQ
    • Testimonials
    • Mailing List
    • Contact
    • About

How to Add Devices to VeraLite

19/9/2015

 
Adding Z-Wave devices to Vera Lite
Whilst perhaps not immediately obvious to some people, it's actually possible to add devices to your VeraLite directly and without needing to rely on the Vera GUI. This is achieved by temporarily operating the controller on battery power and simply carrying it around the house to where your Z-Wave devices are physically installed. This is particularly useful in situations where you need to add or remove devices that are fixed and cannot be moved (eg a hard-wired relay switch) or when they are not within direct range of your Vera.

Step 1. Disconnect the power and LAN cables from the back of your VeraLite and insert a fresh set of 4x AA batteries (the battery compartment is located at the bottom of the device).

Step 2. Press and hold the "Battery" button for 3 seconds, then wait for the blue "Power" light to appear solid. Shortly after, the orange "Ready" light will start blinking once per second indicating that your VeraLite is in include mode.

Step 3. Before adding a device, we recommended that you first exclude it to ensure it's in its factory default state. To exclude a device, you will need to tap the "-" button. The orange "Ready" light will start blinking twice per second. Follow your device's exclude procedure and you will see the "Ready" light flutter briefly as a confirmation that your device was detected and successfully excluded.

Step 4: To include a device, you will need to tap the "+" button. The "Ready" light will blink once per second. Follow your device's include procedure and you will see the "Ready" light flutter briefly as a confirmation that your device was detected and successfully included. 

Step 5: Repeat steps 3 & 4 for any other devices you need to add.

Step 6. To save your changes and exit the battery mode, press and hold the "+" button for 5 seconds. You can then plug your VeraLite back into mains power and LAN and proceed to configuring your newly added devices via the Vera GUI.


Comments are closed.

    Categories

    All
    Fibaro
    Getting Started
    Home Assistant
    Info & Discussion
    Product News
    Reviews
    Vera/Ezlo
    Z-Wave

    Archives

    March 2022
    October 2021
    August 2021
    July 2021
    June 2021
    May 2021
    April 2021
    October 2020
    September 2020
    August 2020
    July 2020
    April 2020
    December 2019
    October 2019
    May 2019
    April 2019
    November 2018
    August 2018
    July 2018
    June 2018
    March 2018
    January 2018
    November 2017
    October 2017
    September 2017
    May 2017
    December 2016
    September 2016
    August 2016
    July 2016
    June 2016
    May 2016
    April 2016
    February 2016
    January 2016
    October 2015
    September 2015
    August 2015
    July 2015
    June 2015
    April 2015
    March 2015
    January 2015
    December 2014
    November 2014
    October 2014
    September 2014

    RSS Feed

Search
Australian Z-Wave Home Automation Shop
SHOP
​Featured Products​
Z-Wave
Security​
Shopping Cart
Contact Us
CUSTOMER SERVICE
Contact Us
Mailing List
Orders, Shipping & Returns
Privacy Policy
Terms of Service
About Us, Reviews and Testimonials
MORE INFO
About Us
Testimonials
Blog
FAQ​
Free Shipping on most orders
FREE SHIPPING
Australia-wide on all orders over $200
Secure payment - PayPal and major cards accepted
SECURE PAYMENTS
PayPal & major cards accepted
The best prices in Australia for Z-Wave Home Automation Products
LOWEST PRICES
Found a cheaper price? Contact us!
ABN: 24 548 417 566
© 2022 RKM Smart Home. All Rights Reserved.
By using this site, you consent to our Terms of Service.​